Serving the Roseville area  ·  (279) 529-5726  ·  Open Mon-Sun 7am-7pm
📞 (279) 529-5726 Free Quote

Metal Roofing in Rocklin, CA (95677) · Local Professionals

Roseville Metal Roofing · Fast response in Rocklin and the Roseville area · Free estimate 24h

✅ Licensed Contractor 🛡️ Licensed & Insured 💸 Free Quote 24h 🕐 Mon-Sun 7am-7pm
+222Verified Reviews
10Years in Business
4.9 ★Google Rating
24/7Available
✅ No hidden fees💳 Cards accepted🛡️ Licensed & Insured

Rocklin sits where the flat valley floor starts to roll up into oak-studded foothills, and the housing stock tells that story block by block. You have granite-country subdivisions like Whitney Ranch and Sunset West with two-story stucco homes under concrete tile, older single-story ranches closer to Pacific Street with wide eaves and low-pitch composition roofs, and hillside custom homes off Clover Valley Road that catch every bit of afternoon sun and winter wind. That mix means one metal roofing plan does not fit every lot in 95677.

Homeowners here call Roseville Metal Roofing because we work this ground every week, from the tight side yards near Rocklin Elementary to the larger ranchette parcels out toward the foothill edge. We know how delta breezes push rain against the west-facing slopes, how oak limbs drop on roofs after a dry summer, and how fast a failed fastener turns into a ceiling stain. We are based in Roseville and serve Rocklin and the surrounding Placer County area, and we are fully insured with general liability and workers' compensation.

Metal Roofing in Rocklin (95677)

Rocklin's terrain is the first thing that shapes a roofing job. The flat-to-rolling ground near Rocklin Road and the older downtown blocks is clay and hardpan, so winter rain sheets off rather than soaking in, and that puts a premium on gutters and flashing details. Up the slopes in Whitney Ranch, Sunset West, and the Clover Valley hills, roofs take more wind and more sun, and access gets tighter. Many of these lots have narrow side yards, sloped driveways, and mature valley oaks and live oaks hanging over the ridgeline, so we plan staging and fall protection around the trees, not through them. Hillside homes often need standing seam or stone-coated steel because those profiles shed debris and reflect heat better than aging composition or concrete tile. On the older bungalows and ranches, we frequently find layered shingles, dry underlayment, and reused flashing, which means a metal roof over shingles only makes sense after we confirm the deck and the existing layers meet code.

Our team has installed, repaired, and replaced metal roofs across Rocklin and the greater Roseville area, from single-story retirement homes to two-story family houses and small agricultural buildings. We handle standing seam, corrugated and ribbed panels, metal shingle, stone-coated steel, and copper and specialty metal, plus the gutters, snow guards, and flashing that keep a metal roof performing. We pull the permit, coordinate any HOA or historic review, and document the job for your records.

Our services in Rocklin

How a Job Works in Rocklin

Step 1: You call (279) 529-5726 or request a free estimate. We schedule an on-site assessment, walk the roof and the attic if accessible, check fasteners, seams, flashing, and deck condition, and talk through what you are seeing (a leak, a lifted panel, a roof at the end of its life). We give you a written scope and a clear price before any work starts.

Step 2: We confirm the Rocklin permit through the city building department and, when your neighborhood has one, coordinate the HOA design review for panel profile and color. On the day of work, we protect landscaping, stage materials where the truck can safely reach, and keep the crew off your oak roots. Tight side yards and sloped drives in Whitney Ranch and the older blocks near Pacific Street get extra planning so we are not blocking neighbors or damaging fences.

Step 3: We clean the site daily, magnet the yard and driveway for fasteners, and do a final walkthrough with you. We show you the finished roof, the flashing details, and the gutter flow, and we leave the property as clean as we found it. You get the paperwork you need for warranty and insurance records.

Pricing in Rocklin depends on roof size, pitch, access, deck condition, and how much old material has to come off. As a ballpark, metal roof installation starts around $8 per square foot, standing seam around $10, metal roof replacement around $9, and a metal roof over shingles retrofit around $7. Corrugated and ribbed panel roofing starts near $5.50, metal shingle and stone-coated steel around $9, and copper or specialty metal around $20. Repairs and leak repairs start around $450, screw replacement and re-fastening around $750, flashing and chimney or skylight repair around $600, and metal roof coating or painting around $2.50. Snow guards and ice protection start around $1,200, and gutters for metal roofs start around $9 per linear foot. Storm and wind damage inspections are free, and commercial and agricultural metal roofing estimates are free as well. The honest number comes from seeing your roof, so call (279) 529-5726 for a free estimate.

My Whitney Ranch home has concrete tile and the south slope bakes all afternoon. Is standing seam worth it here?
For a lot of Rocklin hillside and two-story homes, yes. Standing seam reflects heat, sheds oak debris and leaves better than tile, and handles the afternoon delta breezes without the wind-lift issues we see on lighter panels. We look at your pitch, sun exposure, and HOA color rules before recommending a profile, and we can compare it against stone-coated steel if you want a tile-like look.
A winter storm peeled back panels on my roof near Clover Valley Road. How fast can you respond?
Call (279) 529-5726 and we will schedule an inspection as quickly as we can. We can secure lifted or separated panels, tarp an active leak, and document the damage with photos and measurements for your insurance file. We never promise coverage, but we do give you the paperwork your adjuster will ask for.
What does a typical metal roof replacement cost in Rocklin, and what moves the price?
Most full replacements land in a range that starts around $9 per square foot for metal roof replacement, with standing seam and stone-coated steel higher and retrofits over shingles lower. Size, roof pitch, number of layers to remove, deck repairs, access, and flashing complexity are the big swing factors. A free on-site estimate at (279) 529-5726 gives you a real number instead of a guess.
Do I need a permit from the City of Rocklin for a metal roof, and does the historic district change anything?
A full replacement or re-roof commonly requires a permit, and the thresholds, fees, and inspection requirements are set by the local building department, so we verify the current rules with the City of Rocklin before work starts. If your property is in a historic area or has design review, that can affect panel profile and color. We handle the permit paperwork and coordinate the review so you are not chasing it yourself.
My neighbor's oak hangs over my property line and drops limbs on my roof. What can I do?
Property line and tree questions are civil matters, so we do not give legal advice, but we can inspect and repair the roof damage and document what we find with photos. If your HOA has rules about tree maintenance or roof color, we can coordinate with them on the roofing side. For the tree itself, talk with your neighbor first and check your city and HOA guidelines.
What kind of insurance coverage do you carry for work on my Rocklin home?
We are fully insured, with general liability and workers' compensation.
What maintenance does a metal roof need in Rocklin's climate?
The main things we see here are fastener backing out after years of thermal cycling, debris buildup in valleys and behind chimneys, and flashing seals drying out in the summer UV. We recommend an inspection after the winter storm season and again before fire season, plus keeping oak limbs off the roof and gutters clear. A coating refresh every several years can extend the life of older panels.
Why choose us?

Trusted professionals in Roseville

🏅

Licensed contractors

Continuous training, professional equipment, meticulous and code-compliant work

🛡️

Licensed & Insured

Full coverage on all our job sites, no exceptions

⚡

Available Mon-Sun 7am-7pm

Emergencies, weekends, holidays: available when you need us

💰

100% Free Quote

Response within 24h, no commitment, by phone or form

Our services

Our Metal Roofing Services in Roseville

All your work handled by qualified professionals in Roseville

Metal Roof Installation

Complete metal roof systems engineered for your local climate and built to outlast three shingle roofs.

Included in your service

  • Deck inspection and repair before any panel goes on
  • High-temp synthetic underlayment and correct ridge and soffit ventilation
  • Manufacturer-certified panel, trim, and flashing details for the full warranty
  • Free on-site assessment and written estimate within 24h
Learn more→

Standing Seam Metal Roofing

Concealed-fastener standing seam: no exposed screws to loosen, leak, or need re-torquing.

Included in your service

  • Panels roll-formed to the exact length of your roof, no end laps
  • Mechanically seamed or snap-lock profiles with concealed clips
  • Floating clip system that lets panels expand and contract freely
  • Kynar 500 / PVDF finish in the full architectural color range
Learn more→

Metal Roof Replacement

Full tear-off of an end-of-life shingle, cedar, or metal roof, replaced with a complete new system.

Included in your service

  • Tear-off and haul-away of the old roofing, dumpster included
  • Decking inspected board by board, rot and soft spots replaced
  • New underlayment, drip edge, valleys, and penetration flashing throughout
  • Documentation of the finished system for your insurer or future buyer
Learn more→

Metal Roof Over Shingles (Retrofit)

Retrofit metal installed over sound existing shingles: no tear-off, less waste, lower cost.

Included in your service

  • Honest deck and shingle assessment first, recover only when it is the right call
  • Furring strips or slip sheet as the panel profile and local code require
  • Existing vents, pipe boots, and flashings reworked to the new roof plane
  • Straight guidance on when tear-off is the better long-term choice
Learn more→

Metal Roof Repair

Targeted repair of damaged, loose, or storm-hit metal roofing before it reaches your ceiling.

Included in your service

  • Bent, dented, or punctured panels replaced and color-matched
  • Seams, laps, and penetrations resealed with compatible butyl and sealant
  • Failed pipe boots, closures, and ridge cap fasteners renewed
  • Written findings with photos of what we found and what we fixed
Learn more→

Metal Roof Leak Repair

Priority leak response: we trace the leak to its real source instead of caulking the symptom.

Included in your service

  • Water testing and interior tracing to find the true entry point
  • Backed-out fasteners, separated seams, and flashing gaps corrected at the cause
  • Emergency tarping available same day after a storm
  • Attic and insulation moisture check so hidden damage does not sit and spread
Learn more→

Screw Replacement & Re-Fastening

The top cause of leaks on 15 to 30 year old screw-down roofs, fixed for a fraction of replacement.

Included in your service

  • Every fastener replaced with oversized screws and new EPDM sealing washers
  • Dried-out washers and stripped holes addressed panel by panel
  • Ridge, eave, and sidewall closures renewed at the same time
  • Restores a watertight roof without replacing sound panels
Learn more→

Corrugated & Ribbed Panel Roofing

Corrugated, tuff-rib, and 5V panel roofing: the budget-friendly workhorse for homes and outbuildings.

Included in your service

  • Galvalume and painted steel panels cut to length on site
  • Correct screw pattern and torque so washers seat without over-driving
  • Foam and metal closures at ridge, eave, and rake to keep weather and pests out
  • Full color range for homes, cabins, barns, and workshops
Learn more→

Metal Shingle Roofing

The look of architectural shingle, slate, or shake with the lifespan and wind rating of steel.

Included in your service

  • Interlocking stamped steel or aluminum shingle panels
  • Walkable finished surface, easier to service than a standing seam field
  • Lightweight enough for retrofit over an existing roof structure
  • Profiles and colors that suit historic and HOA-governed neighborhoods
Learn more→

Stone-Coated Steel Roofing

Steel strength under a textured stone finish, with strong hail and wind performance.

Included in your service

  • Acrylic-bonded stone granule surface over structural steel
  • Battened or direct-to-deck installation depending on the profile
  • Class A fire rating and high impact resistance ratings
  • Tile, shake, and shingle textures for suburban and coastal homes alike
Learn more→

Copper & Specialty Metal Roofing

Copper, zinc, and aluminum for porches, bay windows, dormers, and full architectural roofs.

Included in your service

  • In-house fabrication of pans, valleys, and custom curved details
  • Soldered seams and joints where the detail calls for it
  • Isolation of dissimilar metals to prevent galvanic corrosion
  • A living patina that develops over decades of service
Learn more→

Metal Roof Coating & Painting

Restoration for faded, chalking, or surface-rusted metal, adding 10 to 15 years without replacement.

Included in your service

  • Wash, degrease, and mechanical prep of the entire panel surface
  • Rust treatment and primer on affected areas before topcoat
  • High-performance elastomeric or silicone coating system applied to spec
  • Honest assessment first: we say so when the roof is past coating
Learn more→

Flashing, Chimney & Skylight Repair

Flashing is the number one leak point on any metal roof, and it is what we fabricate best.

Included in your service

  • Custom bent step, counter, and apron flashing made in-house
  • Chimney crickets to shed water on the uphill side
  • Skylight curbs and head flashing rebuilt to the panel profile
  • Valley and wall transition details closed with matching trim
Learn more→

Snow Guards & Ice Protection

Snow retention that stops rooftop avalanches onto decks, gutters, walkways, and entryways.

Included in your service

  • Pad-style guards or continuous rail systems matched to your panel
  • Layout calculated from roof pitch, panel length, and local snow load
  • Clamp-on mounting on standing seam, no panel penetrations
  • Ice dam and eave detailing for higher-elevation homes
Learn more→

Storm & Wind Damage Repair

Wind, hail, and fallen-limb repair with thorough documentation and a straight repair-or-replace answer.

Included in your service

  • Free post-storm inspection with dated photo documentation
  • Emergency tarping and temporary weatherproofing when needed
  • A written report you can use when documenting your insurance claim
  • Honest assessment of repair versus replacement, with no pressure either way
Learn more→

Metal Roof Inspection

A written, no-obligation assessment of fastener condition, seams, flashing, and remaining service life.

Included in your service

  • Fastener, washer, and seam condition checked across the field
  • Flashing, penetrations, and closures inspected point by point
  • Coating wear, chalking, and corrosion graded panel by panel
  • Written report with photos and a straight answer on years remaining
Learn more→

Gutters for Metal Roofs

Gutters sized and hung correctly for metal roofing, where standard hangers and spacing do not work.

Included in your service

  • Seamless aluminum or half-round systems formed on site
  • Hanger placement and spacing matched to the panel profile
  • Oversized capacity and downspouts sized for heavy regional rainfall
  • Bracket spacing tightened for high-wind zones so storms do not tear the gutter off
Learn more→

Commercial & Agricultural Metal Roofing

Barns, workshops, churches, and light commercial metal roofing across the county.

Included in your service

  • Long-run panels for wide spans and low-slope structures
  • Purlin and framing attachment detailed for the building type
  • Insulation, vapor barrier, and condensation control options
  • Repairs and re-fastening for aging agricultural metal buildings
Learn more→
Verified client reviews

222+ Verified Client Reviews in Roseville

⭐⭐⭐⭐⭐ 4.9/5 · 222 verified Google reviews

Free Quote

Get Your Free Quote

Metal Roofing in Roseville · Response within 24h · No commitment · ☎ (279) 529-5726

Your Free Quote Request

Confidential · Response within 24h

✅ Free personalized estimate ⚡ Response within 24h 🛡️ Licensed & Insured 📍 On-site visits included in Roseville ✅ No hidden fees 🕐 Available Mon-Sun 7am-7pm